Device Configuration

The Device Configuration tab is used to set defaults appropriate for the types of devices being supported via the DSM16 connection. The screen varies depending on whether you have a DSM16P Card (plugs into Galaxy Expand or Galaxy Express chassis) or a DSM16 Module (standalone). 

Device Configuration tab - DSM16P Card

The DSM16P Card supports either Norstar/BCM or M1/CS1000 style digital sets. Therefore, the Device Configuration tab settings controls whether the card is to be used with Norstar/BCM sets or with M1/CS1000 sets. To adjust any of these settings:

  1. Open the UCX Digital Station Module Web-based Configuration Utility
  2. From the Gateway tab, select Device Configuration and adjust the settings as required
  3. Once you have made the desired changes, press Save Changes

DSM16pJitterBuffer.png


 

Property Value Description
Digital Set Mode

 

Norstar/BCM
or
M1/CS1000
or
IP Office 95xx

 
You can configure the DSM16P Card for supporting Norstar/BCM compatible digital sets, M1/CS1000 compatible digital sets, or Avaya IP Office 9504 or 9508 digital sets.. You cannot mix the types of sets on a single card.

Default Setting: Norstar/BCM

Relocation

 

Enabled
or
Disabled
Controls whether the sets retain their programming when changed to a different port or if the programming stays associated with the port itself. (Note: Set Relocation is not supported for the IPOffice 95XX setting.)
New Call Volume

 

System Default 
or
User Selected
Controls whether a new call is presented at the system default volumes or at the last settings as adjusted by the user
 
Jitter Buffer
 
Enabled
or
Disabled
or
Server Controlled
Controls whether the Jitter Buffer is permanently on or off, or if the UCX should decide when to use it.

 

TX Gain
(UCX to phone)
-15 dB to +15 dB
(Default: 0 db)
Controls the level of the audio as sent from the UCX to the digital phone.  (Drag slider or click at a location on slider to set value.)
RX Gain
(phone to UCX)
-15 dB to +15 dB
(Default: 0 db)
Controls the level of the audio as sent from the digital phone to the UCX.  (Drag slider or click at a location on slider to set value.)

 

When you switch from Norstar/BCM to either M1/CS1000 or the IP Office 95xx settings you must be sure that you have disconnected the Norstar/BCM sets from the amphenol interface on the module before applying changes as the power levels on the M1/CS1000 and IP  settings can cause damage to Norstar/BCM sets.

 

 

When you switch from a lower power configuration to one requiring higher power, you will see the following type of warning. 

DSM16pConfigWarning.png


Once you have ensured that all lower voltage sets have been disconnected, press OK.

DSM16pDeviceConfig.png

Locating the DSM16P card

The DSM16P card may be one of many in a single or multiple Galaxy Expand chassis or even in one or more Galaxy Express chassis. It is possible to determine which card corresponds with the particular IP address to which you are logged in, by using the Identify button on the Device Configuration page.

  1. Click on the Identify button.
  2. You will be notified that the status LED will begin flashing an alternating red and green for a period of 10 seconds. 
    DSM16pIdentify.png
  3. Observe which of the DSM16 cards displays the flashing LED. If the DSM16P card is in a remote location, have someone local to the chassis verify the flashing pattern.

Device Configuration tab - DSM16 Module (Discontinued)

The DSM16 Module only supports Norstar/BCM digital sets. Therefore, the Device Configuration tab only displays settings that are appropriate for the Norstar/BCM sets. To adjust any of these settings:

  1. Open the UCX Digital Station Module Web-based Configuration Utility
  2. From the Gateway tab, select Device Configuration and adjust the settings as required
  3. If you wish to return to the original settings, click Defaults
  4. Once you have made the desired changes, press Save Changes

DSM16mJitterBuffer.png

 
Property Value Description
Digital Set Mode Norstar/BCM You can only configure the DSM16 Module for Norstar/BCM mode
Relocation

 

Enabled
or
Disabled
Controls whether the sets retain their programming when changed to a different port or if the programming stays associated with the port itself.
New Call Volume

 

System Default 
or
User Selected
Controls whether a new call is presented at the system default volumes or at the last settings as adjusted by the user
 
Jitter Buffer
 
Enabled
or
Disabled
or
Server Controlled
Controls whether the Jitter Buffer is permanently on or off, or if the UCX should decide when to use it.

 

TX Gain
(UCX to phone)
-15 dB to +15 dB
(Default: 0 db)
Controls the level of the audio as sent from the UCX to the digital phone.  (Drag slider or click at a location on slider to set value.)
RX Gain
(phone to UCX)
-15 dB to +15 dB
(Default: 0 db)
Controls the level of the audio as sent from the digital phone to the UCX.  (Drag slider or click at a location on slider to set value.)
 
Page Tags: 
survivable
redundancy