The X10 SIP Paging Gateway is a SIP enabled multifunctional IP audio device dedicated for industry users. It can convert voice streams from the UCX system to analogue sounds for background music, public address, intercom, etc.
X10 Paging Gateway | |
Mini screwdriver and 4 mounting screws | |
Phoenix connector | |
Grounding cable | |
Network cable |
Power | 12V 2A input. Power supply is not included. Device can be powered via PoE. |
---|---|
Reset button | Press and hold the reset button for at least 5 seconds then release. The device will play the voice prompt and the system reboots. After factory settings are successfully restored, the system LED will be flashing. |
Volume + / - | Press the volume + and - buttons simultaneously for 3 seconds and the device will announce the device's IP address through the connected speakers. |
ETH0+POE | 10/100 MPS supports PoE. |
ETH1 | 10/100 MPS. |
Dry Contact Signal - Normally-Open Output - Common Input - Normally-Closed Output |
There are 3 connectors for Dry Contact Signal. |
Digital Level Input + / - | There are 2 connectors for Digital Level Input. |
Button1 LED + / - and Switch + / - | There are 4 connectors for Call Button 1. |
Button2 LED + /- and Switch + / - | There are 4 connectors for Call Button 2. |
Speaker Right + / - and Speaker Left + / - |
The are 4 connectors for speaker wiring. The + is for amplified output. This is for connecting directly to speakers. The – is non-amplified. This is used for connecting to an amplified speaker or stereo amplifier. |
Audio IN / OUT jacks |
3.5mm jacks for audio input and output. The audio out jack can be used for headphones or small speakers. |
Install device securely in desired location using the provided mounting screws.
Attach the grounding cable and proceed to connect Speakers and other external equipment to the device as desired.
Using the mini screwdriver, loosen the screws for the desired speaker connection slots on the phoenix connector. Insert the LEFT and RIGHT speaker wires into the lower position and tighten the screws. |
|
Repeat the above step to connect wires for additional equipment as desired. | |
Once all the wiring is complete, Insert the phoenix connector into the Paging Gateway. |
Connect the network cable from port ETH0 on the device to a PoE enabled switch port.
Or connect the power supply (not included) to a power outlet.
Wait for the device to complete its power on.
By default, the network mode is DHCP. Press and hold the VOL+ and VOL- buttons simultaneously for 3 seconds, the device will announce the device's IP address.
Take note of the IP address.
Launch a browser window and enter the IP address of the Paging Gateway.
Login using the default login credentials:
The X10 Paging Gateway (PG) supports up to 3 SIP accounts: One primary and two secondary accounts. The primary and secondary accounts can be used to whichever is the primary function of the paging unit.
In our example below, we will use the primary account for the "warehouse ringer" and one secondary account for paging announcements.
From the Paging Gateway's web interface, navigate to SIP Settings -> Primary SIP Account page and perform the following steps:
In this example, the purpose of the primary account is just to play a ringtone in the warehouse and not answer the call. The primary SIP extension should be included in a Ring Group to trigger the ring along with any telephones that are supposed to ring. The PG device will never answer a call, its function is to just ring.
Navigate to the Secondary SIP Account 1 page and repeat the above steps to create the secondary SIP account:
In this example, the purpose of the secondary account is to automatically answer and broadcast the announcement.
You can test the setup by calling the secondary SIP extension directly. The PG unit will auto-answer the call and broadcast.
When the paging group number is called (e.g. *700), a paging tone is played first then the PG unit will start broadcasting.
Navigate to Advanced -> Volume page to adjust the volume level of the speakers:
Click on the Submit button to save the settings.